• Procesador de audio, Limitador Compresor de 5 bandas con generador Estéreo digital.
• Separación mayor de 70 dB.
• Entradas y salidas AES/EBU Y Audio analógico balanceado.
• Mini SD para Back-up de Audio.
• ETHERNET RJ45, Gestión WEB SERVER Y SNMP (V 2.0).
• Cumple con RDS/RBDS integrado y dinámico.
• UECP EBU SPB490 CENELEC Y NRSC, y con todo el protocolo para UE y EEUU.
• Entrada para Streaming (MP3, OPUS, PCM, VORBIS, ETC).
• Salida IP de 20KHz (MP3, OPUS, PCM, VORBIS) Para WEB
• Streaming ICECAST y SHOUTCAST.
• Changeover de audio automático.
• Decodificador MPX.

Brochure_COM-LIM-70_OMB

La entrada Procesador de Audio COM LIM 70 se publicó primero en DBTC | Digital Broadcasting & Telecommunications Colombia.

• Procesador de Audio, Limitador compresor de 5 bandas con generador Estéreo digital.
• Separación Mayor de 70 dB.
• Entradas y salidas AES/EBU y audio analógico balanceado.
• Mini SD para Back-up de audio.
• Ethernet RJ45, Gestión web Server y SNMP (V 2.0).
• Cumple con RDS/RBDS Integrado y dinámico.
• UECP EBU SPB490 CENELEC y NRSC, y con todo el protocolo para UE y EEUU.
• Changeover de audio manual.
• Decodificador MPX.

Brochure_COM-LIM-60_OMB

La entrada Procesador de Audio COM LIM 60 se publicó primero en DBTC | Digital Broadcasting & Telecommunications Colombia.

• User-Friendly Interface
• Configuration: Stereo.
• Impedance: >10kΩ load impedance, electronically balanced
• Nominal Input Level: Software adjustable from –9.0 to +13.0 dBu (VU).
• Connectors: Two XLR-type, female, EMI-suppressed. Pin 1 chassis ground, Pins 2 (+) and 3 electronically balanced, floating and symmetrical.
• A/D Conversion: 24 bit 128x oversampled delta sigma converter with linear-phase anti- aliasing filter. Converter outputs 64 kHz sample rate, which the 5500i then decimates to 32 kHz in DSP using an ultra-high-quality image-free synchronous sample rate converter. In strand-alone stereo encoder mode, 64 kHz output of converter is not down- sampled.
• Filtering: RFI filtered.
• Analog Audio Output
  Configuration: Stereo. Flat or pre-emphasized (at 50μs or 75μs), software-selectable.
• Source Impedance: 50Ω, electronically balanced and floating.
• Load Impedance: 600Ω or greater, balanced or unbalanced. Termination not required or recommended.
• Output Level (100% peak modulation): Adjustable from –6 dBu to +24 dBu peak, into 600Ω or greater load, software-adjustable.
• Signal-to-Noise: >= 90 dB unweighted (Bypass mode, de-emphasized, 20 Hz–15 kHz bandwidth, referenced to 100% modulation).
• L/R Crosstalk: <= –70 dB, 20 Hz–15 kHz.
• Distortion: <= 0.01% THD (Bypass mode, de-emphasized) 20 Hz–15 kHz bandwidth.
• Connectors: Two XLR-type, male, EMI-suppressed. Pin 1 chassis ground, Pins 2 (+) and 3 electronically balanced, floating and symmetrical.
• D/A Conversion: 24 bit 128x oversampled, with high-pass filter at 0.15 Hz (–3 dB).
• Filtering: RFI filtered.
• Digital Audio Input
  Configuration: Stereo per AES3 standard, 24 bit resolution, software selection of stereo, mono from left, mono from right or mono from sum.
• Sampling Rate: 32, 44.1, 48, 88.2, or 96 kHz, automatically selected.
• Connector: XLR-type, female, EMI-suppressed. Pin 1 chassis ground, pins 2 and 3 transformer balanced and floating, 110Ω impedance.
• Input Reference Level: Variable within the range of –30 dBFS to –10 dBFS.
• J.17 De-emphasis: Software-selectable.
• Filtering: RFI filtered.
• Digital Audio Output
  Configuration: Stereo per AES3 standard. Output configured in software as flat or pre- emphasized to the chosen processing pre-emphasis (50μs or 75μs), with or without J.17 pre-emphasis.
• Sample Rate: Internal free running at 32, 44.1, 48, 88.2 or 96 kHz, selected in software. Can also be synced to the AES3 digital input at 32, 44.1, 48, 88.2 or 96 kHz, as configured in software.
• Word Length: Software selected for 24, 20, 18, 16 or 14-bit resolution. First-order high-pass noise-shaped dither can be optionally added, dither level automatically adjusted appropriately for the word length.
• Connector: XLR-type, male, EMI-suppressed. Pin 1 chassis ground, pins 2 and 3 trans- former balanced and floating, 110Ω impedance.
• Output Level (100% peak modulation): –20.0 to 0.0 dBFS software controlled. Filtering: RFI filtered.
• Wordclock/10 MHz Sync Reference Input
  Configuration: Accepts 1 x wordclock or 10 MHz reference signals, automatically selected. The DSP master clock can be phase-locked to these signals, which in turn phase-locks the 19 kHz pilot tone frequency, facilitating singe-frequency network operation. The digital output sample frequency can also be locked to these signals.
• Level: Unit will lock to 1 x wordclock and 10 MHz squarewaves and sinewaves having a peak value of 0.5 V to 5.0 V.
• Connector: BNC female, grounded to chassis, non-terminating to allow reference signals to be looped through via an external BNC “tee” connector (not supplied).
• Composite Baseband Output
  Configuration: Two outputs, each with an independent software-controlled output level control, output amplifier and connector.
• Source Impedance: 0Ω voltage source or 75Ω, jumper-selectable.
• Load Impedance: 37Ω or greater. Termination not required or recommended.
• Maximum Output Level: +16.0 dBu (13.82Vp-p).
• Pilot Level: Adjustable from 6.0% to 12.0%, software controlled.
• Pilot Stability: 19 kHz, ±1.0 Hz (10 degrees to 40 degrees C).
• D/A Conversion: 24-bit
• Signal-to-Noise Ratio: >= 85 dB (Bypass mode, de-emphasized, 20 Hz – 15 kHz band- width, referenced to 100% modulation, unweighted).
• Distortion: <= 0.02% THD (Bypass mode, de-emphasized, 20 Hz – 15 kHz bandwidth, referenced to 100% modulation, unweighted).
• Stereo Separation: > 50 dB, 30 Hz – 15 kHz. 60 dB typical at 400 Hz.
• Crosstalk-Linear: <= –80 dB, main channel to sub-channel or sub-channel to main channel (referenced to 100% modulation).
• Crosstalk-Non-Linear: <= –80 dB, main channel to sub-channel or sub-channel to main channel (referenced to 100% modulation).
• 38 kHz Suppression: >= 70 dB (referenced to 100% modulation).
• 76 kHz & Sideband Suppression: >= 80 dB (referenced to 100% modulation).
• Pilot Protection: 60 dB relative to 9% pilot injection, ±250 Hz (up to 2 dB composite processing drive).
• Subcarrier Protection (60-100 kHz): >= 70 dB (referenced to 100% modulation; with up to 2 dB composite limiting drive; measured with 800 line FFT analyzer using “maximum peak hold” display).
• 57 kHz (RDS/RBDS) Protection: 50 dB relative to 4% subcarrier injection, ±2.0 kHz (up to 2 dB composite processing drive).
• Connectors: Two BNC, shell connected to chassis ground, EMI suppressed.
• Maximum Load Capacitance: 0.047 microfarad (0Ω source impedance). Maximum cable length of 100 feet/30 meters RG–58A/U. Filtering: RFI filtered.
• Subcarrier (SCA) Inputs
  Configuration: Two subcarrier inputs sum directly into composite baseband outputs; COMPx LVL control settings have no effect on the absolute subcarrier levels.
• Impedance: 600Ω
• SCA Sensitivity: Variable from <100 mV p-p to >10 V p-p to produce 10% injection assuming 100% modulation = 4 V p-p at the 5500’s composite outputs. Rear-panel accessible PC-board-mounted trim pots allow user to adjust the sensitivities of the two SCA inputs.
• Connectors: Two BNC, shell connected to chassis ground, EMI suppressed.
• 19 kHz Pilot Reference: SCA2 input can be re-jumpered to provide a 19 kHz pilot reference output.
• Remote Computer Interface
  Supported Computer and Operating System: IBM-compatible PC running Microsoft Windows® 2000 (SP3 or higher) or XP, ME vista 7, and 8, 8.1 and 10
• Configuration: TCP/IP protocol via direct cable connect, modem, or Ethernet interface. Suitable null modem cable for direct connect is supplied. Modem and other external equipment is not supplied.
• Serial Connector:> RS–232 on DB–9 male connector, EMI-suppressed. Uses PPP to pro- vide for direct or modem connection to the 5500i PC Remote application.
• Ethernet Connector: Female RJ45 connector for 10-1000 Mbps networks using CAT5 cabling. Native rate is 100 Mbps. Provides for connection to the 5500i PC Remote application through either a network, or, using a crossover Ethernet cable, directly to a computer.
• Ethernet Networking Standard: TCP/IP.
• Remote Control (GPI) Interface
  Configuration: Eight (8) inputs, opto-isolated and floating.
• Voltage: 6–15V AC or DC, momentary or continuous. +12VDC provided to facilitate use with contact closure.
• Connector: DB–25 male, EMI-suppressed.
• Control: User-programmable for any eight of user presets, factory presets, bypass, test tone, stereo or mono modes, analog input, digital input.
• Tally Outputs
  Circuit Configuration: Two NPN open-collector outputs.
• Voltage: +15 volts maximum. Do not apply negative voltage. When driving a relay or other inductive load, connect a diode in reverse polarity across the relay coil to protect the driver transistors from reverse voltage caused by inductive kickback.
• Current: 30 mA maximum
• Indications: Tally outputs can be programmed to indicate a number of different operational and fault conditions, including Input: Analog, Input: Digital, Analog Input Silent, AES Input Silent, and AES Input Error.
• Power
  Voltage: 85–264 VAC, 50–60 Hz, 30 VA.
• Connector: IEC, EMI-suppressed. Detachable 3-wire power cord supplied.
• Fuse:> 2.5A 20mm Quick Acting HBC, mounted on the power supply circuit board.
• Grounding: In order to meet EMI standards, circuit ground is hard-wired to chassis ground.
• Safety Standards: ETL listed to UL standards, CE marked.
• Environmental
  Operating Temperature: 32° to 122° F / 0° to 50° C for all operating voltage ranges.
• Humidity: 0–95% RH, non-condensing.
• Dimensions (W x H x D): 19” x 1.75” x 14.25” / 48.3 cm x 4.5 cm x 36.2 cm. One rack unit high.
• Humidity: 0–95% RH, non-condensing.
• RFI/EMI: Tested according to Cenelec procedures. FCC Part 15 Class A device.
• Shipping Weight & Dimensions: 18 lbs / 8.2 kg – 23″ x 23″ x 6″
• Warranty
  Five Years, Parts and Service: Subject to the limitations set forth in Orban’s Standard Warranty Agreement.
• Because engineering improvements are ongoing, specifications are subject to change without notice.

La entrada Procesador de audio Orban Optimod 5500i FM se publicó primero en DBTC | Digital Broadcasting & Telecommunications Colombia.

• Frequency Response
• +/-0.5dB 20Hz to 15kHz, 17.5kHz in extended mode
• Signal to Noise Ratio
• Greater than -80dBu de-emphasized, 20Hz to 15kHz
• System Distortion
• Less than 0.01% THD below pre-emphasis, in audible above
• Stereo Separation
• 65dB minimum, 20Hz to 15kHz, 70dB typical
• Digital Output Level
• Adjustable from -24.0dBFS to 0.0dBFS in 0.1dB increments
• Stereo Baseband Output
• Adjustable from -2dBU to +22dBU (0.1dBincrements) into 600-Ohms, 20-Ohm output impedance
• A/D Conversion
• Crystal Semiconductor CS5361, 24bit 128x over-sample ddelta sigma converter with linear-phase anti-aliasing filter.
• Pre-ADC anti-alias filter, with high-pass filter at < 10Hz
• D/A Conversion
• Crystal Semiconductor CS4391, 24-bit, 128x oversampled
• Analog I/O
• Two balanced, EMI filtered XLR connectors
• Stereo Generator Connections
• Four 75-Ohm BNC female, twoinputs, two outputs
• Digital I/O
• AES/EBU In&Out via XLR connectors
• Supports stereo digital audio and Omnia Direct
• Ethernet
• Shared RJ45 supporting 100 and 1000BASE-T Ethernet connections
• Power Requirements
• 100-264 VAC, 47-63Hz autosensing, dual PSU
• Power Connector
• Dual IEC male, detachable 3-wire power cords supplied
• Power Supply
• Internal dual redundant
• Environmental
• Operating: 0 to 50 degrees C
• Non-operating: –20 to 70 degrees C.

La entrada Procesador de audio Omnia 7 FM Digital On-Air se publicó primero en DBTC | Digital Broadcasting & Telecommunications Colombia.

• SpecificationsMeasured from balanced XLR inputs to XLR outputs And from digital AES-3 input to AES-3 output
• Inputs1-XLR3 conector, 600 ohms balanced, Nominal level + 4 dBu. Max level + 24 dBu, Software adjusted
  2-RJ45 stereo balanced (compatible with StudioHUB) Nominal level -10 dBu to + 24 dBu, 600 ohms balanced
  3- Digital AES/ EBU input transformer balanced ) Nominal level -18 dBFS Adjust from -24 to 0 dBFS
  4-Optional digital stereo AoIP option for LAN Ethernet or Internet input
  RF Input: Digital Receiver for use as FM Monitor and Audio Analyzer
  VOICE/ MUSIC change: GPI Input = + 5V … +15V for VOICE mode preset (On-Air microphones)
  Voice/Music switch received from console in AoIP models
  Switching between all Music Style Program settings using RDS data from studio.
• Outputs1-Analog Balanced, XLR connector+ 4 dBu; Z= 600, Max + 18 dBu, Flat frequency response
  2- Analog unbalanced RJ45 output (compatible with StudioHUB), + 4 dBu / 600 ohms
  3- Digital AES/ EBU, transformer balanced ) 0 VU at -12 dBFS
  4 & 5 – MPX-1 & MPX-2 for FM transmitters (Normal & Emergency) 0 – 5,5 Vpp
  Independent level software controlled, Z = 50 ohms
  Differential output, BNC connector, floating ground 50 ohms
  Allows 45 dB canceling buzz & noise due to ground loops
  Protected for electrical storms 2 KV overload
  Optional AoIP processed digital output in /AoIP models. It allows for direct audio streaming or for AoIP connection between different studios at the Radio / TV station.
• IN/OUT ControlRemote control by software of the Input – Output matrix
  Remote control by software of the Input – Output matrixAutomatic programable transfer from one input
  to another when audio fail is detected
• Frequency
  ResponseANALOG BAL = 20 – 16.000 Hz +/- 0,3 dB
  AES to AES = 20 – 16.000 Hz +/- 0,3 dB
  measured below compression & limiter threshold
• Harmonic Distortion and DELAYANALOG BAL = Below 0,005 % @ 1 kHz
  AES to AES = Below 0,002 %
  Delay: 3 – 9 ms depending on preset used
• Dynamic
  RangeANALOG BAL to ANALOG BAL > 95 dBA
  AES to AES > 110 dBA
• Stereo
  Separation> 80 dBA
• Subsonic FilterChebyshev 4th order, Selectable: OFF – 15 Hz – 20 Hz
• Asymmetry
  Cancelling5:1 cancelling reduction, using Khann-Bonello system
• Expander5 bands low level expander
• AGCOne Wide-band AGC and 5 bands AGC (Leveller)
• Multiband
  CompressorsFIVE or more bands depending of software version used
  Standard model of 5 bands includes: 5 x AGC (Levellers); 5 x Compressors; 5 x Limiters; 5 x Clippers
  Linear Phase crossover
  Full software control of all parameters
  12 – 16 factory presets programs
• EffectsSuper BASS effect and Stereo Enhancer is standard in all software versiones
  Linear limiters with predictive technology (Look Ahead) gives the audience a full clean sound
• Pre-Processing
  EqualizerFull Parametric EQ with four bands . Each band with 2order passband filter with:
  a) Level control; b) Frequency control; c) Q factor control (bandwidth)
• ProccesingNumber of bands and stages, features, etc are dependent on software version used
  It can work in FM, AM, HD, TV & Streaming modes
  Standard 542APC works in Five bands FM mode 0-50-75 uS
• Power115 V / 230 V (rear switch selected) 50/60 Hz, 20 W
• Dimensions19″ rack mount. Module one (44,4 mm) // weight 3 Kg Net; (4 Kg for courier freight)

Caracteristicas DSP STEREO CODER

• MPX outputTwo MPX outputs with individual remote level control by LAN or Internet
  Differential output, BNC connector, floating ground 50 ohms. Allows 45 dB cancelingbuzz & noise due to ground loops
  Level of each output adjustable from 0 to 5,5 Vpp
• Frequency
  Response20-15.000 +/- 0,2 dB,plus 16 Khz/linear phase filter
  Attenuation at 19 Khz > 80 dB
• Harmonic
  DistortionFrom 30-12.000 Hz, below 0,01 %
  Measured using Belar Digital Stereo decoder DSD-1A and Spectrum Analyzer
• Signal to Noise
  RatioBetter than 85 dBA with reference to 100% modulation
  Measured using Belar Digital Stereo decoder model DSD-1A
• Stereo
  Separation> 65 dB at 1 Khz
• 38 Khz suppressionBelow – 80 dB Ref 100% modulation
• 57, 76 & 95 Khz
  suppressionBelow – 80 dB Ref 100% modulation
• Pilot tone
  stability+/- 0,002 % (+/- 0,5 Hz)Caracetristicas INTERNATIONAL RDS ENCODER
• RDS/RBDS signalConforms to CENELEC EN50067 / EN 62106 /
  Control interface based on ASCII commands and UECP protocol
  Built-in weekly scheduling
• RDS signal bandwidth+/- 2.4 kHz (50 dBc)
• Spurious suppression>90 dB
• Harmonics suppression>80 dB
• Clock referencePilot Tone
• 19 kHz pilot PLL lock bandwidth+/- 2Hz
• Data connector: Ethernet inputRJ45 connector for TCP/IP LAN Ethernet
  Text features include dynamic PS, parsing, scrolling, fixed messages, scheduling and reading from HTTP
• Data Port Speed2400 – 9600 bps
• Supported servicesPI Program Identification, M/S Music/Speech, PS Program Service, PIN Program-Item Number, PTY Program Type, ECC Extended Country Code, TP Traffic Program, RT Radiotext, AF Alternative Frequencies, TDC Transparent Data Channels TA Traffic Announcement, IH In House Applications, PTYN Program Type Name, ODA Open Data Applications, DI Decoder Identification, CT Clock-Time and Date, EON Enhanced Other Networks information.

La entrada 542 APC Procesador Universal FM – AM – HD se publicó primero en DBTC | Digital Broadcasting & Telecommunications Colombia.

• Inputs1-XLR3 conector, level self-adjusted 0 dBu to + 15 dBu 600 ohms balanced
  2-RCA unbal, level self adjusted -15 to 0 dBu, 10 K
  3-RJ45 stereo balanced (compatible with StudioHUB, Axia, etc) 0 dBu to + 15 dBu, 600 ohms balanced
  All with R internal > 10 Kohms
  4-Optional digital stereo USB input for PC direct connection
• Outputs1-Analog Balanced, + 4 dBu; Z= 600 / 10 Kohms, with de-emphasis (flat response)
  2-Optional USB digital stereo input (flat response) for direct connection to PC
• MPX OutputTwo MPX outputs with individual level control with preset at rear side
  600/10 Kohms, level from 0,5 to 4 Vpp
  Differential output, BNC connector, floating ground 50 ohms
  Allows 45 dB canceling buzz & noise due to ground loops
• Frequency
  Response
  20 – 16.000 Hz +/- 0,5 dB measured below compression & limiter threshold
• Harmonic
  Distortion
  Below 0,02 % @ 30-15.000 Hz
• Noise
  Below – 90 dBA ref 100 % modulation
• Stereo
  Separation
  > 75 dBA
• Subsonic Filter
  Chebyshev 2nd order, 15 Hz
• Asymmetry
  Cancelling
  5 : 1 cancelling effect, using Khann-Bonello system
• Expander
  10:1 slope, 0,1 msec attack time, 200 msec release
• AGC (wideband)
  VCA controlled, 30 dB range, 3 sec attack/release
• Multiband
  Compressors
  3 bands, 18 dB/octave,
  Linear Phase crossover
  Compressors: 30 dB range, 5:1 slope,VCA controlled
  Automatic attack time
  Release time user controlled by 3 x ENERGY controls
• IM Cancelled
  Clipper
  IM clipper cancellation > 30 dB below 250 hz
• Dynamic EQ
  0 – 12 dB dynamic boost at Low, Mid and High Frecuency
  Front panel user controlled
• Processing
  7 stages of processing devices
• Power
  115 V / 230 V (rear switch selected) 50/60 Hz, 20 W
• Dimensions
  19″ rack mount. Module one (44,4 mm) // weight 3 Kg Net; (4 Kg for courier freight).
  Stereo Coder – Digital with oversampling 16x (608 kHz)
  Audio input
  2 Vpp for 100 % MPX output (4 Vpp)
  MPX output
  Two MPX outputs with individual level control with preset at rear side
  Differential output, BNC connector, floating ground 50 ohms. Allows 45 dB canceling buzz & noise due to ground loops
  Level of each output adjustable from 0,5 to 4 Vpp 600/10 kohms
  Frequency Response
  20-15.000 +/- 0,2 dB,
  plus 15 Khz/5 order eliptic, Active FDNR, L.P. filter
  Attenuation at 19 Khz > 50 dB
  Harmonic
  Distortion
  From 30-15.000 Hz, below 0,005 %
  Measured using Belar Digital Stereo decoder DSD-1A and Tektronix 5L4 N Spectrum Analyzer
  Signal to Noise
  Ratio
  Better than 90 dBA with reference to 100% modulation
  Measured using Belar Digital Stereo decoder model DSD-1AStereo
  Separation> 65 dB at 1 Khz
  38 Khz suppression
  Below – 70 dB Ref 100% modulation
  57, 76 & 95 Khz
  suppression
  Below – 75 dB Ref 100% modulation
  Pilot tone
  stability
  +/- 0,002 % (+/- 0,5 Hz)

Características del Stereo Coder – Digital with oversampling 16x (608 kHz)

• Audio input2 Vpp for 100 % MPX output (4 Vpp)
• MPX outputTwo MPX outputs with individual level control with preset at rear side
  Differential output, BNC connector, floating ground 50 ohms. Allows 45 dB canceling
  buzz & noise due to ground loops
  Level of each output adjustable from 0,5 to 4 Vpp 600/10 kohms
• Frequency Response20-15.000 +/- 0,2 dB,
  plus 15 Khz/5 order eliptic, Active FDNR, L.P. filter
  Attenuation at 19 Khz > 50 dB
• Harmonic
  DistortionFrom 30-15.000 Hz, below 0,005 %
  Measured using Belar Digital Stereo decoder DSD-1A and Tektronix 5L4 N Spectrum Analyzer
• Signal to Noise
  RatioBetter than 90 dBA with reference to 100% modulation
  Measured using Belar Digital Stereo decoder model DSD-1A
• Stereo
  Separation> 65 dB at 1 Khz
• 38 Khz suppressionBelow – 70 dB Ref 100% modulation
• 57, 76 & 95 Khz
  suppressionBelow – 75 dB Ref 100% modulation
• A41A41A41A41A41A41A41A41A41Pilot tone
  stability+/- 0,002 % (+/- 0,5 Hz)

La entrada Procesador de Audio de FM: AudiMax 362HD se publicó primero en DBTC | Digital Broadcasting & Telecommunications Colombia.

• Gated and ‘windowed’ gain-riding AGC.
• Unique, adjustable ‘syllabic leveling’.
• 3 bands of dynamic compression with selectable crossovers.
• 4 sections of parametric EQ plus an effective ‘Bass Punch’ feature.
• Independent ‘Density’ and ‘Smooth/Loud’ adjustments.
• GPIOs, Web/email/SNMP for controls and alarms.
• Built-in real time clock and headphone Jack.
• Analog, AES-digital, streaming in/outs.
• Selectable US and international cutoff filters.
• A great ‘utility’ processor; ideal ahead of STLs/codecs.
• Full function ‘responsive’ Web interface works on desktop and mobile devices.

La entrada Procesador de audio Novia 236 se publicó primero en DBTC | Digital Broadcasting & Telecommunications Colombia.

• Gated and ‘windowed’ gain-riding AGC.
• Unique, adjustable ‘syllabic leveling’.
• 3 bands of dynamic compression with selectable crossovers.
• 4 sections of parametric EQ plus an effective ‘Bass Punch’ feature.
• Independent ‘Density’ and ‘Smooth/Loud’ adjustments.
• GPIOs, Web/email/SNMP for controls and alarms.
• Built-in real time clock and headphone Jack.
• Analog, AES-digital, streaming in/outs (no MPX).
• Selectable 20kHz-wideband and FM-specific processing.
• A great ‘utility’ processor; ideal ahead of STLs/codecs.
• Full function ‘responsive’ Web interface works on desktop and mobile devices.

La entrada Procesador de audio estéreo Novia 262 se publicó primero en DBTC | Digital Broadcasting & Telecommunications Colombia.

• Highest performance 24-bit A/D and D/A convertors.
•  AES67 compatible.
• 8 complete Vorsis multiband processors, each with:- 4-band parametric equalizer
  – 3-way crossover
  – 3 compressors
  – 3 limiters
  – Final lookahead limiter.
• Two 8-channel utility mixers.
• 4 AES digital inputs on RJ-45 and “D” connectors.
• 4 stereo analog inputs on RJ-45 and “D” connectors.
• 4 AES digital outputs on RJ-45 and “D” connectors.
• 4 stereo analog outputs on RJ-45 and “D” connectors.
• Can be used standalone or as part of a WheatNet-IP Intelligent Network.
• Built-in router control.
• Front panel headphone Jack.
• Socketed output chips.
• Front panel metering.
• Rugged power supply.
• Colorful OLED display.
• Silence sensing can be applied to any output.
• One Gigabit Ethernet port.

La entrada Procesador de audio Aura8-IP Blade 3 Wheatstone se publicó primero en DBTC | Digital Broadcasting & Telecommunications Colombia.

• Multiband adaptive iAGC.
• Bass Management System optimized for AM.
• Four-band full parametric equalizer.
• Variable high pass filter and voice phase rotator.
• Ethernet-based remote control via 100BaseT Ethernet and rear panel RJ-45.
• Four GPI preset triggers.
• Front panel OLED and headphone Jack.
• Specially tuned factory presets.
• Guru GUI, for easy setup and navigation.
• WheatNet-IP compatible.
• Front panel setup and configuration menu eliminates the need for a PC during installation.

La entrada Procesador Multibanda AM55 con tecnología IAGC se publicó primero en DBTC | Digital Broadcasting & Telecommunications Colombia.